I'm also attaching a pic of the control module from one i found on eBay. Let me know if you need anymore info or more explanation. With everything plugged in, toggling the switch does not result in any sound being made (the typical clicking sound that occurred when i would lock or unlock the doors)ġ) how often does the power lock control module fail?Ģ) how can i remove the actuator to more easily test it?ģ) does the lack of that sound indicate actuator or this control module?Ĥ) would a failing driver's door actuator cause the other doors to not lock/unlock, or are most likely all 4 door hosed up? This seemed strange to me, but the wires which were supposed to (if I read the diagram correctly) indicate the switch locking/unlocking showed continuity without doing anything to the switch. I then, referencing the wiring diagram in the Haynes manual, tested continuity from the control module to the driver's door lock actuator. That eliminated a bad wire from the switch to the module. I then reconnected the wires and tested them at the other end, where it plugs in to the Power Lock Control module and flipped the switch again. I also tested the switch and it showed continuity for both lock/unlock. The power door locks on my car are not locking/unlocking the doors. However, a locksmith fixed the lock and now the master key works fine, but the PDL problem persists. When this happened, this problem began occurring. One observation: The master key started giving some trouble when unlocking the driver's door, so I started using the valet key. All door locks will now open only when the driver's door is closed OR at least the door locking mechanism is in contact with the door frame (the little latch thing that "holds" the door in place once closed). Likewise, I have always been able to lock all doors with the driver's door open (holding the outside handle up as if opening the door, then pressing the interior lock button, not the switch). I have always been able to unlock all doors with the driver's door open, using the PDL switch. The power door locks work FINE when the driver's door is closed. My '97 Honda Civic (4 doors) power door locks were working properly until recently.
#1997 honda civic tapedeck install how to#
Regardless of your automobile’s repair needs, you can find Acura and Honda body clips and interior trim fasteners that will leave your car as good as new.Here's my questions. Honda Civic Rear Deck/Speaker Removal MrRangerZr1 38.7K subscribers Subscribe 352 51K views 4 years ago Here is how to remove the rear deck panel to get access to your speakers, airbags, and seat. You can also find other commonly replaced parts such as Honda splash shield clips, which are used to secure the shield that protects your car’s underhood from damage and the elements, or Honda Civic plastic fasteners for the interior of your car. Need to replace a fender liner on your Honda Accord? We’ve got you covered with our selection of Honda Accord fender liner clips that can replace old and broken clips. Minor fender bender in your Honda Civic that left your bumper hanging off? Not to worry - with our Honda Civic bumper clips, you can snap your bumper into place securely. Civic Type R power-folding side mirrors Modified front and rear fenders 3M Stone Shield Shinzowerks vinyl graphics 00-Spec Civic hatchback taillights Interior Bride Brix II seats Bride seat. With our large selection of hardware replacement parts for Honda and Acura automobiles, you can easily fix up old clips and fasteners. Honda & Acura Clips, Fasteners and Retainers Metric Small Head Philips Pan Machine Screws JIS B 1111.Metric JIS Phillips Indented Hex Head SEMS Screws.General Purpose Depressed Center Wheels.Aluminum Oxide Resin Bonded Cut-Off Wheels.Drill Bits, Spot Weld, Saws, Cut Off Wheels.Nylon, Rubber & Polyethylene Connectors.Steel Tubing Clamps With Neoprene Jacket.Partial Stainless Steel Screw-Worm Gear Type-Hose Clamps.Norma Torro (European Style) Hose Clamps.All Stainless Steel Screw-Worm Gear Type-Hose Clamps.
0 kommentar(er)
